![[Main Page]](/modules/mediawiki/images/mediawiki.png)
| Revision as of 14:35, 29 September 2014 (edit) pzebelloni (Talk | contribs) (→One) ← Previous diff |
Revision as of 14:37, 29 September 2014 (edit) pzebelloni (Talk | contribs) (→One - HW1) Next diff → |
||
Line 11: |
Line 11: | ||
| A USB-to-TTL UART cable is required. | A USB-to-TTL UART cable is required. | ||
| - | UART required signals are: RXD, TXD, RTS, DTR, GND and Power. | + | UART required signals are: '''RXD, TXD, RTS, DTR, GND and Power'''. |
| Signals direction is indicated from the point of view of HW1 board. | Signals direction is indicated from the point of view of HW1 board. | ||
Line 18: |
Line 18: | ||
| ! <div align="left">One PIN#</div> | ! <div align="left">One PIN#</div> | ||
| ! <div align="left">Name</div> | ! <div align="left">Name</div> | ||
| - | ! <div align="left">Mode</div> | + | ! <div align="left">Mode / Direction</div> |
| ! <div align="left">UART</div> | ! <div align="left">UART</div> | ||
| ! <div align="left">Remarks</div> | ! <div align="left">Remarks</div> | ||
Line 24: |
Line 24: | ||
| |- | |- | ||
| | | 1 | | | 1 | ||
| - | | | GND | + | | | '''GND''' |
| | | Power | | | Power | ||
| - | | | GND | + | | | '''GND''' |
| | | Power & Signal Reference | | | Power & Signal Reference | ||
| |- | |- | ||
| | | 2 | | | 2 | ||
| - | | | /RST | + | | | '''/RST''' |
| | | IN | | | IN | ||
| - | | | DTR | + | | | '''DTR''' |
| | | MSP RESET Signal | | | MSP RESET Signal | ||
| |- | |- | ||
| | | 3 | | | 3 | ||
| - | | | BSL_TX | + | | | '''BSL_TX''' |
| | | OUT | | | OUT | ||
| - | | | RXD | + | | | '''RXD''' |
| | | TX Data (ONE -> Host/PC) | | | TX Data (ONE -> Host/PC) | ||
| |- | |- | ||
| | | 4 | | | 4 | ||
| - | | | TEST | + | | | '''TEST''' |
| | | IN | | | IN | ||
| - | | | RTS | + | | | '''RTS''' |
| | | MSP TEST Signal | | | MSP TEST Signal | ||
| |- | |- | ||
| | | 5 | | | 5 | ||
| - | | | BSL_RX | + | | | '''BSL_RX''' |
| | | IN | | | IN | ||
| - | | | TXD | + | | | '''TXD''' |
| | | TX Data (One <- Host/PC) | | | TX Data (One <- Host/PC) | ||
| |- | |- | ||
| | | 6 | | | 6 | ||
| - | | | VDD | + | | | '''VDD''' |
| | | Power | | | Power | ||
| - | | | +3V3 | + | | | '''+3V3''' |
| | | +3.3 [VDC] Power Supply | | | +3.3 [VDC] Power Supply | ||
| |} | |} | ||
Revision as of 14:37, 29 September 2014
Hardware Requirements
A free USB port is required to update HardWaves devices.
Surfer
No additional hardware is required to update Surfer, since it connects directly on USB.
One - HW1
A USB-to-TTL UART cable is required.
UART required signals are: RXD, TXD, RTS, DTR, GND and Power.
Signals direction is indicated from the point of view of HW1 board.
| One PIN#
| Name
| Mode / Direction
| UART
| Remarks
|
|---|---|---|---|---|
| 1 | GND | Power | GND | Power & Signal Reference |
| 2 | /RST | IN | DTR | MSP RESET Signal |
| 3 | BSL_TX | OUT | RXD | TX Data (ONE -> Host/PC) |
| 4 | TEST | IN | RTS | MSP TEST Signal |
| 5 | BSL_RX | IN | TXD | TX Data (One <- Host/PC) |
| 6 | VDD | Power | +3V3 | +3.3 [VDC] Power Supply
|