Firmware Update

From C-Labs Home

Revision as of 14:35, 29 September 2014 (edit) pzebelloni (Talk | contribs) (→One) ← Previous diff		Revision as of 14:37, 29 September 2014 (edit) pzebelloni (Talk | contribs) (→One - HW1) Next diff →
Line 11:		Line 11:
	A USB-to-TTL UART cable is required.		A USB-to-TTL UART cable is required.
-	UART required signals are: RXD, TXD, RTS, DTR, GND and Power.	+	UART required signals are: '''RXD, TXD, RTS, DTR, GND and Power'''.
	Signals direction is indicated from the point of view of HW1 board.		Signals direction is indicated from the point of view of HW1 board.
Line 18:		Line 18:
	! <div align="left">One PIN#</div>		! <div align="left">One PIN#</div>
	! <div align="left">Name</div>		! <div align="left">Name</div>
-	! <div align="left">Mode</div>	+	! <div align="left">Mode / Direction</div>
	! <div align="left">UART</div>		! <div align="left">UART</div>
	! <div align="left">Remarks</div>		! <div align="left">Remarks</div>
Line 24:		Line 24:
	|-		|-
	| | 1		| | 1
-	| | GND	+	| | '''GND'''
	| | Power		| | Power
-	| | GND	+	| | '''GND'''
	| | Power & Signal Reference		| | Power & Signal Reference
	|-		|-
	| | 2		| | 2
-	| | /RST	+	| | '''/RST'''
	| | IN		| | IN
-	| | DTR	+	| | '''DTR'''
	| | MSP RESET Signal		| | MSP RESET Signal
	|-		|-
	| | 3		| | 3
-	| | BSL_TX	+	| | '''BSL_TX'''
	| | OUT		| | OUT
-	| | RXD	+	| | '''RXD'''
	| | TX Data (ONE -> Host/PC)		| | TX Data (ONE -> Host/PC)
	|-		|-
	| | 4		| | 4
-	| | TEST	+	| | '''TEST'''
	| | IN		| | IN
-	| | RTS	+	| | '''RTS'''
	| | MSP TEST Signal		| | MSP TEST Signal
	|-		|-
	| | 5		| | 5
-	| | BSL_RX	+	| | '''BSL_RX'''
	| | IN		| | IN
-	| | TXD	+	| | '''TXD'''
	| | TX Data (One <- Host/PC)		| | TX Data (One <- Host/PC)
	|-		|-
	| | 6		| | 6
-	| | VDD	+	| | '''VDD'''
	| | Power		| | Power
-	| | +3V3	+	| | '''+3V3'''
	| | +3.3 [VDC] Power Supply		| | +3.3 [VDC] Power Supply
	|}		|}

---

Revision as of 14:37, 29 September 2014

Hardware Requirements

A free USB port is required to update HardWaves devices.

Surfer

No additional hardware is required to update Surfer, since it connects directly on USB.

One - HW1

A USB-to-TTL UART cable is required.

UART required signals are: RXD, TXD, RTS, DTR, GND and Power.

Signals direction is indicated from the point of view of HW1 board.

One PIN#	Name	Mode / Direction	UART	Remarks
1	GND	Power	GND	Power & Signal Reference
2	/RST	IN	DTR	MSP RESET Signal
3	BSL_TX	OUT	RXD	TX Data (ONE -> Host/PC)
4	TEST	IN	RTS	MSP TEST Signal
5	BSL_RX	IN	TXD	TX Data (One <- Host/PC)
6	VDD	Power	+3V3	+3.3 [VDC] Power Supply